See below for guides to connect to and utilize the various Summit SOM 8M Plus DVK peripherals:

Display - HDMI

The default image for the Summit SOM 8M Plus DVK supports HDMI video output at resolutions up to 4k @ 30fps via the onboard HDMI connector (CON6). Connect an HDMI cable to a compatible display and the CON6 connector to utilize the HDMI output.

Supported Resolutions:

  • 720x480 @ 60fps
  • 1280x720 @ 60fps
  • 1920x1080 @ 120fps
  • 3840x2160 @ 30fps

Display - LCDIF

The default image for the Summit SOM 8M Plus DVK supports up to 1920x1200 @ 60fps per LCDIF if no more than 2 instances are used simultaneously, or 2x 1920x1080 @ 60fps + 1x 4k @ 30fps on HDMI if all 3 instances are used simultaneously

  • One LCDIF drives MIPI DSI, up to UWHD and WUXGA
  • One LCDIF drives LVDS Tx, up to 1920x1080 @ 60fps
  • One LCDIF drives HDMI Tx, up to 4k @ 30fps

LVDS

Two LVDS ports are available on the Summit SOM 8M Plus DVK: J24 and J23. Connect an HDMI cable to a compatible display and one of the available LVDS ports via an LVDS-to-HDMI adapter to utilize the LVDS output.

MIPI DSI

One MIPI DSI port is available on the Summit SOM 8M Plus DVK: J22. Connect a MIPI DSI OLED display to utilize the MIPI DSI output.

Camera - MIPI CSI

The default image for the Summit SOM 8M Plus DVK supports up to two camera inputs as shown in the following table:

# of Cameras Resolutions Supported
1 Up to 12MP @ 30fps or 4k @ 45fps
2 Up to 1920x1080 @ 80fps

Two MIPI CSI ports are available on the Summit SOM 8M Plus DVK: J20 and J21. Connect a MIPI CSI camera module to one of the available MIPI CSI ports to utilize the camera input.

Audio

The Summit SOM 8M Plus offers a broad range of audio input/output solutions including a Cadence® Tensilica® HiFi 4 DSP (operating at up to 800 MHz) and ASRC functionality.

Input

The Summit SOM 8M Plus DVK supports audio input via the following interfaces:

  • HDMI eARC/ARC
  • Combo headphone/mic jack

Output

The Summit SOM 8M Plus DVK supports audio output via the following interfaces:

  • HDMI
  • Combo headphone/mic jack

CAN

The Summit SOM 8M Plus supports 2 CAN interfaces which are routed on the DVK to a Texas Instruments TCAN1046V-Q1 transceiver and exposed on header J27 as described below:

Pin Number Description
1 CAN2 L
2 CAN2 H
3 Ground
4 CAN1 L
5 CAN1 H

UART

The Summit SOM 8M Plus supports 4 onboard UART interfaces, and the DVK board adds an additional 4 via a Maxim MAX14830 Quad Serial UART bridge which are described below:

UART Name Linux Device Path Description
UART1 /dev/ttymxc0 IG60 Serial Module (J14)
UART2 /dev/ttymxc1 Cortex-A53 debug
UART3 /dev/ttymxc2 NXP 88W8997 radio - Bluetooth
UART4 n/a Cortex-M7 debug
MAXUART0 /dev/ttyMAX0 Routed to header J17
MAXUART1 /dev/ttyMAX1 Routed to header J18
MAXUART2 /dev/ttyMAX2 Routed to header J13
MAXUART3 /dev/ttyMAX3 Routed to BL5340 module (MOD2)

I2C

The Summit SOM 8M Plus supports 6 I2C interfaces and, combined with the DVK, a number of peripherals/devices are available as described below:

I2C Interface Name Devices
I2C1 PMIC - NXP PCA9450 (0x25)
I2C2 USB Power Delivery PHY IC - NXP PTN5110 (0x50)
Charger IC - TI BQ25792 (0x6b)
MIPI CSI1
MIPI DSI
LVDS0
LVDS1
I2C3 IO Expander - NXP PCA6416A (0x20)
Columb counter - Microchip PAC1932 (0x10)
MIPI CSI2*
Audio codec - Cirrus Logic WM8960 (0x1a)
Audio accessory detection switch - TI TS3A227E(0x3b)
I2C4 n/a, pins reserved
I2C5 n/a, pins reserved
I2C6 Routed to headers J25 and J26

*Address depends on devicetree configuration

LTE Cell Modem (Quectel EG25-G)

The Summit SOM 8M Plus DVK features an onboard Quectel EG25-G Cat. 4 LTE cellular module which can be used simultaneously with the Wi-Fi and Bluetooth available on the SOM itself. The Quectel EG25-G is supported and managed by ModemManager

Inserting the SIM Card

The Summit SOM 8M Plus DVK supports the nano (4FF) SIM card form factor, and the slot is located on the underside of the main PCB at CON9.

Powering on the LTE Cell Modem

The LTE cell modem is powered off by default. To enable it, enter the following command:

modem on

Now, the LTE cell modem will boot up and enumerate with ModemManager. Standard ModemManager/NetworkManager commands can now be used to bring the cellular connection online. Check with your cellular provider for the appropriate connection settings (e.g., APN).

Additionally, the modem can be disabled again with the following command:

modem off